High Quality 1 RPM Gear Box Auger Motor- Extended Life

Gleason-Avery 1 RPM High Quality Auger Motor GA Part #s 901

(needle bearings for extended life - better than ball bearings)

This 1 RPM auger motor fits many Englander, Enviro, Hudson River, Travis, Whitfield, Austroflamm, Regency and Pellet Master pellet stoves. See below for specific makes and models. This motor is the highest quality gearbox motor made by Gleason-Avery with stall torque at 200 in lbs truly the workhorse of the line to help prevent auger jams compared to other common motors that are approx. 155 in lbs. Rugged, trouble-free. Our most popular gearbox motor based upon superior performance. The auger motor turns the auger, which transfers the pellets from the hopper to the burn pot. It feeds the fire and keeps the flame going. The auger motor must be replaced if it slows down or skips under a load (gears are stripped in the gear box when turning the auger.) See below for compatible models and specifications. In older stoves the auger may stop when the stove gets hot. This may mean the auger motor needs replacing. Please consult a professional in your area to determine that this is the issue. 


For a 1 RPM auger motor with hole for hitch pin in shaft for newer Breckwell and Hudson River models, see the following page where this auger is sold separately.

1 RPM Motor with Hole in Shaft

 

115 Volts  SP/Open  .5 Amp  1 RPM

Continuous duty, Impedance Protected
CCW rotation, viewing from rear
3 in. body  Skeleton frame  1 in. x 3/8 in. shaft

 

These Motors are set up for clockwise rotation (most pellet stoves use this setting). The rotation can be reversed if needed.
 

This auger motor fits these pellet stove makes and models: 

 

Englander (England Stove Works) Pellet Stoves Part# PU-047040
Set to clockwise rotation looking from rear of stove.
Enviro Pellet Stoves (Envirofire): 1 RPM part # EF-001
Needs to be set for counter clockwise rotation looking from rear of stove.
 

Meridian

Evolution A

Omega

EF5

EF2

EF3Bi

Windsor

Milan

Empress

Mini-A

M55

 

 Whitfield Pellet Stoves: 1 RPM part # 1204630

 Needs to be set for counter clockwise rotation looking from rear of stove.
 

 Advantage I (WP2)

Advantage II (WP2)

Advantage II-T (WP2)

Advantage III (WP2)

Advantage II-T Classic (WP2)

Advantage Plus (WP7)

Optima 2

Optima 3

Profile 20

Profile 30

Cascade (WP5)

Explorer

Frontiersman

T300P - (T301P, T305P, T308P) Whitfield Feed System

Legend (WP1)

Prodigy I (WP3)

Prodigy II (WP3)

Quest (WP4)

Quest Plus (WP4)

Waterford Erin

Renaissance

Travis Industries Pellet Stoves (Avalon and Lopi): 1 RPM part # 90-0191
Needs to be set for counter clockwise rotation looking from rear of stove.
 

Lopi Yankee

Lopi Pioneer

Lopi Leyden

Avalon Newport

Avalon Astoria

Avalon Arbor

 

Austroflamm Pellet Stoves

Needs to be set for counter clockwise rotation looking from rear of stove.
Integra

Wega


Regency Pellet Stoves: 1 RPM motor part # GF55-001 or W190570 

 Needs to be set for counter clockwise rotation looking from rear of stove.

GF55

GFI55

 

Archgard Pellet Stove: 1 RPM fuel feed motor part # 305-0046

Needs to be set for counter clockwise rotation looking from rear of the stove.

 

Optima PS-1

 

Pellet Master Pellet Stoves: 1 RPM gear box motor 

Needs to be set for counter clockwise rotation looking from rear of the stove.

Titan 3000

Pellet Master pellet stoves that have not been upgraded to the new brass bushing/new bearing, and have blue or green bearings, need the bushing kit upgrade PM 01-140004 - WHS - PM Brass Bushing Kit All Pellet Stove Models. We do not carry this kit.

 

Also fits Heat N Glo pellet stoves. Check your owners manual for compatible models. 

Other cross reference numbers: 4515U1-063, Whitfield Quest, 93-0194, 12046300, ECM-6, EMC6216, V07524ACD9, Traditions & Profile series stoves, Merkle-Korff, National steel Crafters, Lennox Hearth 6216, Earth stove, Pellet Master R7-RGM451, V08038AA09, 6216, CAR003, 6807, 4515UI-063, MOD 734, 4515UI-050 V003, HM-RGM451, 4515ui-6

 

 

Needs to be set for counter clockwise rotation looking from rear of stove.Needs to be set for counter clockwise rotation looking from rear of the stove